http://southernhogcontrol.net/wiki/ 2026-04-19T17:13:49+00:00 http://southernhogcontrol.net/wiki/ http://southernhogcontrol.net/wiki/lib/tpl/dokuwiki/images/favicon.ico text/html 2021-12-15T12:07:11+00:00 Anonymous (anonymous@undisclosed.example.com) http://southernhogcontrol.net/wiki/doku.php/wiki:camera:3g:installation:characteristics?rev=1639588031&do=diff CAMERA CHARACTERISTICS This manual is intended to visually guide users through the individual steps to properly program, operate and maintain the 3G GSM version of our JAGER PRO M.I.N.E™ and I.C.E.™ Cameras. 1. Antenna: Standard antenna shown receives cell tower signals. Our 5 decibel booster antenna is available as an accessory for operation in low signal areas. text/html 2021-12-15T12:07:11+00:00 Anonymous (anonymous@undisclosed.example.com) http://southernhogcontrol.net/wiki/doku.php/wiki:camera:3g:installation:deployment?rev=1639588031&do=diff CAMERA DEPLOYMENT Align the 1/4 by 20 threads of the T-Post mounting bracket to the camera mounting port. Thread the mounting bracket no more than three complete rotations into the camera mounting port. Then tighten using the adjusting nut. Forcing external threads to the bottom will damage the camera mounting port and the camera housing. text/html 2021-12-15T12:07:11+00:00 Anonymous (anonymous@undisclosed.example.com) http://southernhogcontrol.net/wiki/doku.php/wiki:camera:3g:installation:login_fail?rev=1639588031&do=diff LOGIN FAIL CORRECTIVE ACTION Users should always test their camera at a new location prior to erecting a feeder or a trap enclosure. Move the selector switch from OFF to SETUP. The screen will display “Checking Network”. Allow approximately 20 to 30 seconds for the camera to acquire a cellular signal. If the camera does not automatically connect to the cellular network within 60 seconds, the standard antenna is not sufficient at this location and the camera will be unable to send … text/html 2021-12-15T12:07:12+00:00 Anonymous (anonymous@undisclosed.example.com) http://southernhogcontrol.net/wiki/doku.php/wiki:camera:3g:installation:quick_start?rev=1639588032&do=diff QUICK START PROGRAMMING Begin programming the M.I.N.E™ Camera for operation by removing the protective cap and installing the standard antenna onto the antenna jack. Ensure the black rubber O-ring is not removed from the antenna jack threads. Twist the antenna base snug but do not over tighten. text/html 2021-12-15T12:07:12+00:00 Anonymous (anonymous@undisclosed.example.com) http://southernhogcontrol.net/wiki/doku.php/wiki:camera:3g:installation:sending_photos?rev=1639588032&do=diff MANUALLY SENDING PHOTO Our 3G camera is designed to test program settings and SIM card service by manually sending a photo. Move the selector switch from OFF to SETUP. Allow the camera 30 seconds to search the wireless 3G network. AT&T will appear in the top center of the LCD screen after connecting. Pressing the OK button will immediately capture a photo and upload the image to the network by following the camera program settings. text/html 2021-12-15T12:07:12+00:00 Anonymous (anonymous@undisclosed.example.com) http://southernhogcontrol.net/wiki/doku.php/wiki:camera:3g:installation:sms_codes?rev=1639588032&do=diff SMS COMMAND CODES The SMS Switch must be ON for the camera to receive text commands and was previously covered under the WIRELESS menu tab. The M.I.N.E™ Cam is able to receive text commands from up to four phone numbers to perform 22 different functions remotely. All four phone numbers have the ability to send and receive SMS commands to control the camera. text/html 2021-12-15T12:07:13+00:00 Anonymous (anonymous@undisclosed.example.com) http://southernhogcontrol.net/wiki/doku.php/wiki:camera:3g:installation:timing?rev=1639588033&do=diff TIMING CAMERA TRANSMITTER TO CONTROL BOX RECEIVER THIS STEP IS ONLY A FUNCTION OF THE 3G M.I.N.E.™ CAMERA. THE 3G I.C.E.™ CAMERA DOES NOT UTILIZE AN INTERNAL TRANSMITTER. The 3G M.I.N.E. Camera has an internal transmitter on the circuit board and must be located within 50 meters of the M.I.N.E.™ Gate to operate correctly. Users must manually calibrate the camera transmitter signal to each control box receiver the first time they are paired together. One camera will operate multi…